What Factors Make A Good Component Video Cable


For numerous years, the common approach of connecting analog video gadgets to eachother has been by means of the 75 ohm coaxial cable. Quite ahead of these cables had been in typical use within the house, broadcast and production houses had been wired with 75 ohm video cable, usually operating composite video. The benefits of 75 ohm video coaxial contain outstanding impedance tolerance (wonderful for protecting against signal reflection, which in turn causes ringing and ghosting), exceptional shield efficiency (critical in a high noise surroundings for instance a Broadcast facility), and low loss (great when 1 requirements to perform video over long distances with out important signal degradation). Not too surprisingly, when component and RGB video turned into widespread use, exactly the same form of cable was utilised to connect them up–the distinction becoming, needless to say, that when you’ll find 3 signals, as in a Y,Pb, and Pr component video cable run, 1 requirements 3 cords to run them in. So, no matter whether these are joined together in a sheath, bonded together in a ribbon configuration, or simply run individually, component video cables often consist of 3 cables that are electrically distinct. Every member of the group of 3 is its very own, individual 75 ohm video coaxial cable, having its very own center conductor and shield. What precisely makes a high-quality component video cable? It genuinely comes down to several technical factors. Using typical cable lengths as well as a cable of realistic parameters, the degree of signal loss to resistance throughout the cable isn’t especially substantial; this is particularly so since resistance results in loss, the loss is linear — it impacts all wavelengths on the signal nearly identically, and so if the screen receives the transmission and changes its amplitude, all the info remains present in spite of the loss of transmission strength. Over reasonable cable run measures (say, under 100 feet), these losses aren’t actually important given that one is working with a cord using a good quality sized center conductor (say, 22 AWG or bigger). But you’ll find technological insufficiencies a component video cable may have, which will have significant effect on transmission quality, specially whereby runs tend to be significantly long to create the impedance of the cord a considerable concern. With full Hi-def component functioning at about 35 MHz (that is 1080i, 1080p/60fps may be twice that), the wave length of the signal, fixed for the rate of propagation inside a high quality coax cable, is approximately 24 feet, creating a good 6 foot component video cable a considerable part of the wave length and possibly an aspect in transmission quality (and, when it comes to 1080p at 60fps, those ranges are cut in half). In summation, the points that produce an superb component video cable are merely dependent on getting a effectively manufactured item with firm specifications and great style. A cable that has tight impedance patience, effective protection, appropriately sized for the cable run and ended with mechanically sturdy connections that make great connection using the equipment jacks and don’t do an excessive amount of to vary the impedance of the entire construction will outshine anything else available on the market. Exotic supplies, great looking connectors, and elegant write-ups appear and vanish; request a specification sheet whenever you shop, and ask for specifics such as signal impedance tolerance, shield-braid coverage, and attenuation diagrams.


For numerous years, the common approach of connecting analog video gadgets to eachother has been by means of the 75 ohm coaxial cable. Quite ahead of these cables had been in typical use within the house, broadcast and production houses had been wired with 75 ohm video cable, usually operating composite video. The benefits of 75 ohm video coaxial contain outstanding impedance tolerance (wonderful for protecting against signal reflection, which in turn causes ringing and ghosting), exceptional shield efficiency (critical in a high noise surroundings for instance a Broadcast facility), and low loss (great when 1 requirements to perform video over long distances with out important signal degradation). Not too surprisingly, when component and RGB video turned into widespread use, exactly the same form of cable was utilised to connect them up–the distinction becoming, needless to say, that when you’ll find 3 signals, as in a Y,Pb, and Pr component video cable run, 1 requirements 3 cords to run them in. So, no matter whether these are joined together in a sheath, bonded together in a ribbon configuration, or simply run individually, component video cables often consist of 3 cables that are electrically distinct. Every member of the group of 3 is its very own, individual 75 ohm video coaxial cable, having its very own center conductor and shield. What precisely makes a high-quality component video cable? It genuinely comes down to several technical factors. Using typical cable lengths as well as a cable of realistic parameters, the degree of signal loss to resistance throughout the cable isn’t especially substantial; this is particularly so since resistance results in loss, the loss is linear — it impacts all wavelengths on the signal nearly identically, and so if the screen receives the transmission and changes its amplitude, all the info remains present in spite of the loss of transmission strength. Over reasonable cable run measures (say, under 100 feet), these losses aren’t actually important given that one is working with a cord using a good quality sized center conductor (say, 22 AWG or bigger). But you’ll find technological insufficiencies a component video cable may have, which will have significant effect on transmission quality, specially whereby runs tend to be significantly long to create the impedance of the cord a considerable concern. With full Hi-def component functioning at about 35 MHz (that is 1080i, 1080p/60fps may be twice that), the wave length of the signal, fixed for the rate of propagation inside a high quality coax cable, is approximately 24 feet, creating a good 6 foot component video cable a considerable part of the wave length and possibly an aspect in transmission quality (and, when it comes to 1080p at 60fps, those ranges are cut in half). In summation, the points that produce an superb component video cable are merely dependent on getting a effectively manufactured item with firm specifications and great style. A cable that has tight impedance patience, effective protection, appropriately sized for the cable run and ended with mechanically sturdy connections that make great connection using the equipment jacks and don’t do an excessive amount of to vary the impedance of the entire construction will outshine anything else available on the market. Exotic supplies, great looking connectors, and elegant write-ups appear and vanish; request a specification sheet whenever you shop, and ask for specifics such as signal impedance tolerance, shield-braid coverage, and attenuation diagrams.

Leave a Reply